1. Imveliso yethu yi-7/16 uhlobo (L29) intambo edibeneyo ye-RF coaxial connector. I-impedance yeempawu zesi siqhagamshelo yi-50 Ohms, eneempawu zamandla aphezulu, i-VSWR ephantsi, i-attenuation encinci, i-intermodulation encinci kunye nokuqina komoya okulungileyo.
Okokuqala, i-7/16 (L29) yethu idityaniswe ne-RF coaxial connector inamandla aphezulu kakhulu okuthwala, anokuphatha ukuya kuthi ga kwi-2 kW yamandla. Oku kuthetha ukuba inokusebenza ngokuzinzileyo nangokuthembekileyo kwizicelo zamandla aphezulu ngaphandle kokukhathazeka malunga nokuphazamiseka komqondiso okanye ukuphazamiseka.
2. Okwesibini, isinxibelelanisi sethu sineVSWR ephantsi kakhulu, oko kukuthi, i-voltage stand wave ratio. Oku kuthetha ukuba inokubonelela ngokugqithiswa komgangatho ophezulu ngelixa unciphisa ukubonakaliswa kwesignali kunye nokulahlekelwa, ngaloo ndlela iqinisekisa ukuchaneka kunye nokuzinza kwesignali.
3. Ukongezelela, isinxibelelanisi sethu sinokunciphisa okuphantsi, oku kuthetha ukuba inokubonelela ngokunciphisa umqondiso ophantsi kakhulu, ukwenzela ukuba kwandiswe amandla kunye nokuzinza kwesignali. Ukongezelela, isinxibelelanisi sethu sine-intermodulation encinci, oku kuthetha ukuba inokunciphisa ngokufanelekileyo ukuphazamiseka kunye nokuphazamiseka phakathi kweempawu ze-frequency ezahlukeneyo, ngaloo ndlela iqinisekisa ukuchaneka kunye nokuzinza kwesignali.
4. Ekugqibeleni, isinxibelelanisi sethu sinomsebenzi ogqwesileyo womoya, oku kuthetha ukuba inokusebenza kwindawo enzima, njengokushisa okuphezulu, umswakama ophezulu, uxinzelelo oluphezulu, njl. Ngelo xesha, inokukhusela ngaphakathi kwekhonkco kwimpembelelo. yokusingqongileyo yangaphandle, ngaloo ndlela yandisa ubomi bayo benkonzo
7/16 Din Male Connector For 1-1/4" Foam Feeder Cable | ||
Umzekelo No. | TEL-DINM.114-RFC | |
Ujongano | IEC 60169-4;DIN-47223;CECC-22190 | |
Umbane | ||
Impedance yophawu | 50ohm | |
Uluhlu lokuphindaphinda | DC-7.5GHz | |
VSWR | ≤1.20@DC-3000MHz | |
3rd Order IM (PIM3) | ≤ -155dBc@2×20W | |
I-Dielectric Withstanding Voltage | ≥4000V RMS,50Hz,kwinqanaba lolwandle | |
I-Dielectric Resistance | ≥10000MΩ | |
Qhagamshelana Ukumelana | UQhagamshelwano lwaseziko ≤0.4mΩ | Uqhagamshelwano lwangaphandle ≤1 mΩ |
Ukukhwelana | I-M29*1.5 yokudibanisa intambo | |
Oomatshini | ||
Ukuqina | Imijikelo yokukhwelana ≥500 | |
Izinto eziphathekayo kunye nokuPlating | ||
Igama lezahlulo | Izinto eziphathekayo | Ukucwenga |
Umzimba | Ubhedu | I-Tri-Metal(CuZnSn) |
Isigquduli | PTFE | - |
Umqhubi wangaphakathi | Phosphor Bronze | Ag |
Ukudibanisa Nut | Ubhedu | Ni |
Gasket | Irabha yeSilicone | - |
ICable Clamp | Ubhedu | Ni |
I-Ferrule | - | - |
Okusingqongileyo | ||
Ubushushu bokusebenza | -45 ℃ ukuya kuma-85 ℃ | |
Ireyithi yokumelana nemozulu | IP67 | |
RoHs (2002/95/EC) | Ukuthobela ngokukhululwa | |
Usapho olufanelekileyo lweCable | I-1-1 / 4 '' intambo yesondlo |
Umzekelo:TEL-DINM.114-RFC
Inkcazo
I-DIN Isinxibelelanisi esiyindoda se-1-1/4″ intambo yokuxheshisela
Izinto eziphathekayo kunye nokuPlating | |
Uqhagamshelwano oluphakathi | Ubhedu / iSilver Plating |
Isigquduli | PTFE |
Umzimba kunye neKondi yangaphandle | Ubhedu / ingxubevange ehlanganiswe nge-tri-alloy |
Gasket | Irabha yeSilicon |
Iimpawu zoMbane | |
Impedance yeempawu | 50 ohm |
Uluhlu lokuphindaphinda | DC~3 GHz |
I-Insulation Resistance | ≥10000MΩ |
Amandla eDielectric | 4000 V rms |
Ukuchasa uqhagamshelwano kwiziko | ≤0.4mΩ |
Ukuchasana noqhagamshelwano lwangaphandle | ≤1.5 mΩ |
Ilahleko yokuFaka | ≤0.12dB@3GHz |
VSWR | ≤1.15@-3.0GHz |
Uluhlu lobushushu | -40 ~ 85℃ |
Into evikela amanzi | IP67 |
Imiyalelo yokuFakelwa kwe-N okanye 7/16 okanye 4310 1/2″ intambo eguquguqukayo kakhulu
Ulwakhiwo lwesinxibelelanisi: ( Fig1 )
A. ngaphambili nut
B. umva nut
C. gasket
Imilinganiselo yokuhluthwa njengoko iboniswe ngumzobo (i-Fig2), ingqalelo kufuneka ihlawulwe ngelixa ihlubula:
1. Umphezulu wesiphelo somqhubi wangaphakathi kufuneka uhlanjululwe.
2. Susa ukungcola okufana nesikali sobhedu kunye ne-burr kwindawo yokugqibela yentambo.
Ukudibanisa indawo yokutywina: Khiya indawo yokutywina ecaleni komqhubi wangaphandle wentambo njengoko kubonisiwe kwidayagram (Fig3).
Ukudibanisa i-nut yangasemva (Fig3).
Dibanisa i nut yangaphambili nasemva ngokukruqula njengoko kubonisiwe kwidayagram ( Figs(5)
1. Ngaphambi kokujija, gcoba umaleko wegrisi yokuthambisa kwi-o-ring.
2. Gcina i-nut yangasemva kunye nentambo ingashukumi, Screw kumzimba weqokobhe elikhulu kumzimba weqokobhe elingasemva. Krwela ezantsi iqokobhe elikhulu lomzimba weqokobhe elingasemva usebenzisa isikrufu senkawu. Ukudibanisa kugqityiwe.